Products. Companies. Trade leads

Products: Bender Slitter Cut-Off Pro-Filler 2000 Bender Gauge Constructed with light weight high-tech, anodized alloys Tapco MAX 20 & Cut-Off capacity: steel up to 0,75 mm (20 ga. 20SWG) aluminum up 1 mm Tapco Benders features: 35,5 cm and 48,0 cm throat deep 6 cm mouth opening hollow core construction; Tapco's patented "Moving Pivot" hinge technology bends without marring materials[...]

EMERGENCY STOP, LOCKED PUSCH BUTTONS Control push-buttons type NEF30 with metal housings are designed to be built into Ø30,5mm holes in consoles, control desks or directly in machines and equipment. There are produced two climatic versions: N/2 (for temperate climate) and W/3 (for tropical and sea climate). Each push button type NEF30 consists of the following units: - a driving unit, called the button drive - one, two or three contact blocks fastened to the drive. Fastening of push-buttons[...]

Marking O-rings that we provide are marked according to a system which gives the inner diameter, cross-section diameter, material code and hardness. Material As a standard we offer o-rings made of NBR 70Sh nitrile rubber. However in our offer you may find hardness types ranging from 30Sh to 90Sh and materials, such as NBR, FPM, EPDM, SIL, delivered also in required color on request. We are able to offer our customers ca. 250 different material mixtures. Certificates Since customers[...]

Technical data ZP 400 Clamp manual/screw Min. Diameter of bent material 200-400 mm Material L 40x4 Engine’s power 2,2 kW dimensions 600x500x1200 mm Weight 500 kg Technical data ZP 500 Clamp hydraulic Min. Diameter of bent material 300-400 mm Material L 50x5 Engine power 2,2 / 4 kW Dimensions 800x750x1300 mm Weight 900 kg Technical data ZP 1000 Clamp hydraulic Min. Diameter of bent material 400-600 mm Material L 75x7 Engine power 3 / 4 kW Dimensions 1000x900x1200[...]

Pressure: 13 to 20 bars Technology: Two-stage screw compressors with oil injection GR 110-200 Capacity: 211 to 442 l/s, 447 to 937 feet/min Engine power: 110 to 200 kW Compressors series GR110-200 are two-stage screw compressors with oil injection, designed for using the air of a higher pressure in the scope from 13 to 20 bars. With the two-stage construction, the low and high pressure sensors are located on the gearbox driven by an electric engine TEFC (protection IP-55, insulation class[...]

Frequency: 50 or 60 Hz Engine power: High-pressure engine produced by DETROIT DIESEL/MTU, series 2000 QAC 1000-1006 3-phase voltage 400 V (50 Hz) - 480 V (60 Hz) Technology: Generator driven by a high-pressure engine QAC 1000-1006 Power scope: 900 to 1125 kVA, 720 to 900 kW PRP Portable generators developed by Atlas Copco company, series QAC are reliable, placed in special containers units for producing electric power. Thanks to a well-designed construction generators QAC can be placed[...]

COBRA MK1 Each element of the new Cobra mk1 was designed with attention to the ergonomy, operator’s health and the environment. With its new system of vibration muffling and an engine meeting the world’s strictest requirements regarding exhaus fumes cleanliness, Cobra mk1 is undoubtedly the combustion demolishing hammer with the greatest in the market wave energy. Stronger wave Cobra mk1 hits harder and more quickly than any other combustion hammer. Its wave energy, 60 J, fully reflects[...]

Patron-block filters are used to clean air from small dry dusts, non-glue and non-explosive. Filter is used in metal, textile and food industry, so every where in production process arise dry pollution. To patron filters are applied "GORE-TEX" and "ULTRA-TOP" inlets. Products available in versions passable with capacity up to 1800m3/h and stationary. Polluted air is sucked from emission zone and go to patron chamber. Pollution accumulate on exterior patron surface. Cleaned[...]

Self-locking suction arms ensure the best extract of air pollutions on working stand in direct, close to emission place. Application of self-stopping joint as well as elastic pipes ensure easy placing of nozzle close to pollution source. Diversity of nozzles as regards diameter, construction and pipes leading make possible to adjust extracting stands to own needs resulting from the scope of works made.[...]

Plasma and gas cutting benches type SWG-B are designed for exhausting dusts, fumes and in case of arising during plasma, gas and laser cutting. Air extraction enable sucking off pollution from place of arising as well as filtering (depending on extracting installation used). Pollution filtration apart from ensuring clean air on the working stand also additionally prevents loss of heat in working hall as well as prevent environment pollution. Elements for plasma or gas cutting are placed on[...]